Adjustable

Angle-bracket anchor WK-D

: Wall supported with MOSO angle-bracket anchor type WK-D.

The MOSO angle-bracket anchor type WK-D with adjustable pressure screw is the ideal solution for supports with continuous angled rail. Any uneveness in the concrete is easily compensated via the adjusting screw.

Your advantages at a glance:

Design perfected through practical experience ... Type WKD ... the perfect adjustment range facilitates compensation for dimensional tolerances
The adjustable pressure strut is easy to move yet securely attached to the masonry bracket, thus enabling full-surface contact to the bearing surface, even in the case of slightly sloping substrates
Wall clearances greater than 200 mm are also possible for increased thermal insulation. As well as our MOSO support brackets, we will also obtain specific approval for our air gap wire anchor based on DIN 1053
We also supply the matching, approved air gap wire anchors at low cost

Angle-bracket anchor WK-D

Product information

Load stages:
Distance from wall:
Height adjustment:
Material:
vidence:

3,5kN - 25,0kN
20 - 200 mm

± 25mm

approved stainless steel
type-testing or structural analysis

Angle-bracket anchor WK-D

Use and application

Particularly suitable for visibly supporting largewall surfaces.
Highly suitable for invisibly supporting short wall surfaces.
Can also be used near corners and edges.
The brackets must be fully supported until the brick mortar has set hard.

Angle-bracket anchor WK-D

View tables

Technical data
Type / Version	Load stage	3,5 kN/back		7,0 kN/back		10,5 kN/back
Type / Version	Distance/wall	Cantilever length K	Bracket height x	Cantilever length K	Bracket height x	Cantilever length K	Bracket height x
	20 - 50	130	150	130	200	130	250
	40 - 70	150	150	150	200	150	250
	60 - 90	170	150	170	200	170	250
	80 - 110	190	150	190	200	190	250
	100 - 130	210	150	210	200	210	250
	120 - 150	230	175	230	250	230	300
	140 - 170	250	175	250	250	250	300
	160 - 190	270	175	270	250	270	300
	180 - 200	290	175	290	250	290	300
	Wall clearances greater than 200 mm available on request
Bracket width	W	100		100		100
Bracket length	L	up to 4000		up to 4000		up to 4000
Max. size of fastener		up to M12		up to M12		up to M16
Shear connector for uncracked concrete ≥ C20/25 (compression zone)		UPAT UKA3 M10x165 distance/edge ar ≥ 110		UPAT UKA3 M12x190 distance/edge ar ≥ 135		UPAT UKA3 M16x215 distance/edge ar ≥ 155
Shear connector for cracked concrete ≥ C20/25 (tension/compression zone)		Fischer FHB II-AS M10x60/60 distance/edge ar ≥ 100		Fischer FHB II-AS M12x75/60 distance/edge ar ≥ 140		Fischer FHB II-AS M16x95/60 distance/edge ar ≥ 140
HK-screw on supporting anchor rail in concrete ≥ C20/25		MHK 38/17 M12x80 MBA 38/17K distance/edge ar ≥ 75		MHK 50/30 M12x80 MBA 50/31 distance/edge ar ≥ 150		MHK 50/30 M16x100 MBA 52/34 distance/edge ar ≥ 200
Values apply for facing bricks 115 mm thick with a superimposed load < 2 storeys, otherwise the anchors must be adapted in accordance with DIN 1053. Other dimensions on request

Recommended anchor selection
Superimposed Load(m)	Load (kN/m)	Bracket length, No. of backs	Load stage	Arrangement L1 / L2 / L3
< 1,50	< 3,105	2000 mm/2R	3,5	500 / 1000 / 500
< 2,00	< 4,140	1500 mm/2R	3,5	250 / 1000 / 250
< 3,00	< 6,210	1750 mm/2R	7,0	375 / 1000 / 375
< 4,50	< 9,315	1500 mm/2R	7,0	375 / 750 / 375
< 6,00	< 12,420	1000 mm/2R	7,0	250 / 500 / 250
< 9,00	< 18,630	1000 mm/2R	10,5	250 / 500 / 250
< 12,00	< 24,840	750 mm/2R	10,5	187,5 / 375 / 187,5
(Assuming a 115 mm wide facing brick with γ=18kN/m³. Note individual evidence of attachment!)

Cross-references of additional information
Subject
Corner support with type WK-Z
Wire binders for suspended facework
Individual evidence of attachment in the anchorage base: Fischer FHB II-AS - For attachment in cracked concrete Hilti HVZ-R - For attachment in cracked concrete Fischer FAZ - For attachment in cracked concrete Hilti HST-R - For attachment in cracked concrete MBA - For attachment to the anchor rail UPAT UKA3 - For attachment in uncracked concrete UPAT UPM 44 - Other attachments
Formation of corners and edges
Abutments for suspended facework: Corner abutments Abutments for expansion joints
Technical regulation governing masonry support (DIN 1053)
Installation instructions: With dowl On anchor rail
Principles for dimensioning masonry support

Errata and technical changes reserved.

Angle-bracket anchor WK-D

Technical drawings

: MOSO angle-bracket anchor type WK-D.

: Lengths dimensioned in accordance with

: Type WK-DV, with offset.

: Type WK-D with wire binder type 1.

: Type WK-DS with long pressure screw.