For supporting walls round corners

Angle-bracket anchor WK-E

The MOSO angle-bracket anchor type WK-E is the typical corner bracket anchor.

It is not necessary to cut the frost-resistant bricks, since the support is not interrupted by gusset plates.

No interfering connecting plates in the area of the masonry, so no need for any additional brick cutting
Many of the components for the MOSO angle bracket anchors are prefabricated; only the connecting plate (central metal component) and the length of the angle need to be cut to size on-site to suit the specific fastening situation (wall clearance, wall length, height). Our high-capacity laser systems (up to 6 kW) cut the connecting plates in seconds, incl. the position inscription.
Each angle element is labelled with assembly instructions and job and position number
Wall clearances greater than 200 mm are also possible for increased thermal insulation. As well as our MOSO support brackets, we will also obtain specific approval for our air gap wire anchor based on DIN 1053
We also supply the matching, approved air gap wire anchors at low cost

Angle-bracket anchor WK-E

3,5kN - 25,0kN
20 - 200 mm

± 25mm
approved stainless steel
type-testing or structural analysis

Angle-bracket anchor WK-E

Particularly suitable for supporting corners
Highly suitable for supporting with continuous angled rails for which the frost-resistant bricks cannot be cut.
The brackets must be fully supported until the brick mortar has set hard.

Angle-bracket anchor WK-E

Technical data
Type / Version	Load stage	3,5 kN/back		7,0 kN/back		10,5 kN/back
Type / Version	Distance/wall	Cantilever length K	Bracket height x	Cantilever length K	Bracket height x	Cantilever length K	Bracket height x
	20 - 50	130	150	130	200	130	250
	40 - 70	150	150	150	200	150	250
	60 - 90	170	150	170	200	170	250
	80 - 110	190	150	190	200	190	250
	100 - 130	210	150	210	200	210	250
	120 - 150	230	175	230	250	230	300
	140 - 170	250	175	250	250	250	300
	160 - 190	270	175	270	250	270	300
	180 - 200	290	175	290	250	290	300
	Wall clearances greater than 200 mm available on request
Bracket width	W	100		100		100
Bracket length	L	up to 4000		up to 4000		up to 4000
Max. size of fastener		up to M12		up to M12		up to M16
Shear connector for uncracked concrete ≥ C20/25 (compression zone)		UPAT UKA3 M10x165 distance/edge ar ≥ 110		UPAT UKA3 M12x190 distance/edge ar ≥ 135		UPAT UKA3 M16x215 distance/edge ar ≥ 155
Shear connector for cracked concrete ≥ C20/25 (tension/compression zone)		Fischer FHB II-AS M10x60/60 distance/edge ar ≥ 100		Fischer FHB II-AS M12x75/60 distance/edge ar ≥ 140		Fischer FHB II-AS M16x95/60 distance/edge ar ≥ 140
HK-screw on supporting anchor rail in concrete > C20/25		MHK 38/17 M12x80 MBA 38/17K distance/edge ar > 75		MHK 50/30 M12x80 MBA 50/31 distance/edge ar > 150		MHK 50/30 M16x100 MBA 52/34 distance/edge ar > 200
Values apply for facing bricks 115 mm thick with a superimposed load < 2 storeys, otherwise the anchors must be adapted in accordance with DIN 1053. Other dimensions on request

Recommended anchor selection
Superimposed Load(m)	Load (kN/m)	Bracket length, No. of backs	Load stage	Arrangement L1 / L2 / L3
< 1,50	< 3,105	1000 mm/2R	3,5	325 / 350 / 325
< 2,00	< 4,140	1000 mm/2R	3,5	325 / 350 / 325
< 3,00	< 6,210	1000 mm/2R	7,0	325 / 350 / 325
< 4,50	< 9,315	1100 mm/2R	7,0	350 / 400 / 350
< 6,00	< 12,420	1100 mm/2R	7,0	350 / 400 / 350
< 9,00	< 18,630	1200 mm/2R	10,5	375 / 450 / 375
(Assuming a 115 mm wide facing brick with γ=18kN/m³. Note individual evidence of attachment!)

Cross-references of additional information
Subject
Corner support with type WK-Z
Wire binders for suspended facework
Individual evidence of attachment in the anchorage base: Fischer FHB II-AS - For attachment in cracked concrete Hilti HVZ-R - For attachment in cracked concrete Fischer FAZ - For attachment in cracked concrete Hilti HST-R - For attachment in cracked concrete MBA - For attachment to the anchor rail UPAT UKA3 - For attachment in uncracked concrete UPAT UPM 44 - Other attachments
Formation of corners and edges
Abutments for suspended facework: Corner abutments Abutments for expansion joints
Technical regulation governing masonry support (DIN 1053)
Installation instructions: With dowl On anchor rail
Principles for dimensioning masonry support

Errata and technical changes reserved.

Angle-bracket anchor WK-E