For masonry as the base of the laying work

Angle-bracket anchor WK-M

: Wall supported with MOSO angle-bracket anchot type WK-M.

The MOSO angle-bracket anchor type WK-M is set into the masonry.
This type of anchor is preferably used whenever the substrate for anchorage does not permit the use of dowels.

In order to minimize the effort involved in installation, the anchors can be individually dimensioned by our engineering office.

Your advantages at a glance:

Due to its large bearing surfaces and high stability as a projecting fastening element, this anchor is ideal for the renovation of old buildings
Wall clearances greater than 200 mm are also possible for increased thermal insulation. As well as our MOSO support brackets, we will also obtain specific approval for our air gap wire anchor based on DIN 1053
We also supply the matching, approved air gap wire anchors at low cost

Angle-bracket anchor WK-M

Product information

Load stages:
Distance from the wall:
Height adjustment:
Material:
Evidence:

3,5kN - 7,0kN
20 - 200 mm

in accordance with the height of the recesszugelassener approved stainless steel
structural analysis

Angle-bracket anchor WK-M

Use and application

Particularly suitable for retroactive supports.
Can also be used at corners and edges.
Height can be adjusted with the aid of larger recesses.
The brackets must be fully supported until the brick mortar has set hard.

Angle-bracket anchor WK-M

View tables

Technical data
Type / AVersion	Load stage	3,5 kN/back			7,0 kN/back
Type / AVersion	Distance/wall	Cantilever length K	Bracket height x	Cantilever length K	Bracket height x	Cantilever length K	Bracket height x
	20 - 50	130	50	≥ Ø80x200	130	50	≥ Ø160x200
	40 - 70	150	50	≥ Ø90x200	150	50	≥ Ø170x200
	60 - 90	170	50	≥ Ø100x200	170	50	≥ Ø190x200
	80 - 110	190	50	≥ Ø120x200	190	50	≥ Ø200x200
	100 - 130	210	50	≥ Ø120x200	210	50	≥ Ø210x200
	120 - 150	230	50	≥ Ø120x200	230	50	≥ Ø230x200
	140 - 170	250	50	≥ Ø120x200	250	50	≥ Ø250x200
	160 - 190	270	50	≥ Ø140x200	270	60	≥ Ø270x200
	180 - 200	290	50	≥ Ø140x200	290	60	≥ Ø300x200
	Wall clearances greater than 200 mm available on request
Bracket width	W	100			100
Bracket length	L	up to 4000			up to 4000
Attachment in mortar		Expanding mortar MG III			Expanding mortar MG III
Attachment in concrete		≥ C12/15			≥ C12/15
Values apply for facing bricks 115 mm thick with a superimposed load < 2 storeys, otherwise the anchors must be adapted in accordance with DIN 1053. Other dimensions on request

Recommended anchor selection
Superimposed Load(m)	Load (kN/m)	Bracket length, No. of backs	Load stage	Arrangement L1 / L2 / L3
< 1,50	< 3,105	2000mm/2R	3,5	500 / 1000 / 500
< 2,00	< 4,140	1500 mm/2R	3,5	250 / 1000 / 250
< 3,00	< 6,210	1750 mm/2R	7,0	375 / 1000 / 375
< 4,50	< 9,315	1500 mm/2R	7,0	250 / 1000 / 250
< 6,00	< 12,420	1000 mm/2R	7,0	250 / 500 / 250
(Assuming a 115 mm wide facing brick with γ=18kN/m³. Note individual evidence of attachment!)

Cross-references of additional information
Subject
Wire binders for suspended facework
Formation of corners and edges
Abutments for suspended facework: Corner abutments Abutments for expansion joints
Technical regulation governing masonry support (DIN 1053)
Principles for dimensioning masonry support

Errata and technical changes reserved.

Angle-bracket anchor WK-M

Technical drawings

: Wall supported with MOSO angle-bracket anchor type WK-M.v

: Lengths dimensioned in accordance with prevailing conditions.

: Type WK-MV, with offset.

: Type WK-M with wire-binder type 1.

: Type WK-MS in the plinth area.