Retainer for fascia facing

Horizontal connectors HV-A

: Fascia anchorage with MOSO horizontal connector type HV-A.

The MOSO horizontal connector type HV-A is a retaining anchor for fascias to prevent the formation of cracks due to differences in movement by the flat roof and facework.

Since the anchor is attached below the support for the flat roof, movement by the flat roof.

Your advantages at a glance:

The MOSO HV-A is ideal for use in the parapet area due to its ability to adapt to the thermal movement of the facing shell; the C rail allows unrestricted upward and downward movement of the masonry connection anchor
Wall clearances greater than 200 mm are also possible for increased thermal insulation. As well as our MOSO support brackets, we will obtain specific approval for our air gap wire anchor, based on DIN 1053, underneath this fastening

Horizontal connectors HV-A

Product information

Lengths:
Distance from the wall:
Material:
Evidence:

600 - 1100 mm
80 - 200 mm
approved stainless steel
structural analysis

Horizontal connectors HV-A

Use and application

for horizontal connections in the fascia area
Anchor spacing ak < 75 cm (at the edge < 37,5 cm)

Horizontal connectors HV-A

View tables

Technical data
Type / Version	Length L	600	850	1100
Type / Version	Distance/wall	Wall anchor	Wall anchor	Wall anchor
	80 - 110	3 x MA-A-085-A4	4 x MA-A-085-A4	5 x MA-A-085-A4
	90 - 145	3 x MA-A-12-A4	4 x MA-A-120-A4
	145 - 200	3 x MA-A-180-A4	4 x MA-A-180-A4	5 x MA-A-180-A4
	Wall clearances greater than 200 mm available on request
Width	W	75	75	75
Max. size of fastener		bis M12	bis M12	bis M12
Shear connector for uncracked concrete ≥ C20/25 (Tension/Compression zone)		UPAT UKA3 M10x130 Distance from edge ar ≥ 100	UPAT UKA3 M10x130 Distance from edge ar ≥ 100	UPAT UKA3 M12x160 Distance from edge ar ≥ 120
Verbundanker für gerissenen Beton ≥ C20/25 (Zug- u. Druckzone)		Fischer FHB ll-AS M10x60/20 Distance from edge ar ≥ 100	Fischer FHB ll-AS M12x75/25 Distance from edge ar ≥ 100	Fischer FHB ll-AS M12x75/25 Distance from edge ar ≥ 100
HK screw on supporting anchor rail in concrete ≥ C20/25		MHK 38/17 M12x30 MBA 38/17 l=150 mm Distance from edge ar ≥75	MHK 38/17 M12x30 MBA 38/17 l=150 mm Distance from edge ar ≥75	MHK 38/17 M12x30 MBA 38/17 l=150 mm Distance from edge ar ≥75
Values apply for facing bricks 115 mm thick and a building height <= 20m above ground, otherwise the anchors must be adapted in accordance with DIN 1053. Other dimensions on request

Cross-references for additional informationen
Subject
Wall anchors Type MA-A
Individual evidence of attachment in the anchorage base: Fischer FHB II-AS - For attachment in cracked concrete Hilti HVZ-R - For attachment in cracked concrete Fischer FAZ - For attachment in cracked concrete Hilti HST-R - For attachment in cracked concrete MBA - For attachment to the anchor rail UPAT UKA3 - For attachment in uncracked concrete UPAT UPM 44 - Other attachments
Technichal regulation governing masonry support (DIN 1053)
Principles for dimensioning masonry support