For retroactive anchorage in the masonry

Single-bracket anchors EK-M

The MOSO single-bracket anchor type EK-M is a masonry bracket ensuring reliable support on existing buildings.

The anchors can be individually dimensioned to solve difficult cases.

Constant stock of standard sizes for fast delivery
Slim design prevents the need for costly and laborious chiselling and drilling
Ideal for softer substrates, particularly during façade refurbishments
Wall clearances greater than 200 mm are also possible for increased thermal insulation. As well as our MOSO support brackets, we will also obtain specific approval for our air gap wire anchor based on DIN 1053
Matching, approved air gap wire anchors included in delivery

Single-bracket anchors EK-M

3,5kN - 7,0kN
20 - 200 mm

approved stainless steel
type-testing or structural analysis

Single-bracket anchors EK-M

• For retroactive invisible support for wall sufaces.

• Variable anchor spacing (ak) at 25 cm intervals, depending on load.

• Cannot be used near corners and edges.

• Install anchors at intervals ak and loosely fit intermediate brackets type WA-Z in between if necessary.

• The brackets must be fully supported until the brick mortar has set hard.
For retroactive invisible support for wall sufaces.
Variable anchor spacing (ak) at 25 cm intervals, depending on load.
Cannot be used near corners and edges.
Install anchors at intervals ak and loosely fit intermediate brackets type WA-Z in between if necessary.
The brackets must be fully supported until the brick mortar has set hard.

Single-bracket anchors EK-M

Technical data
Type / Version	Load stage	3,5 kN		7,0 kN
Type / Version	Distance/wall	Cantilever length K	Bracket height x	Cantilever length K	Bracket height x
	20 - 50	130	72	130	91
	40 - 70	150	72	150	91
	60 - 90	170	72	170	91
	80 - 110	190	80	190	101
	100 - 130	210	80	210	101
	120 - 150	230	87	230	106
	140 - 170	250	87	250	106
	160 - 190	270	87	270	106
	180 - 200	290	87	290	106
	Wall clearances greater than 200 mm available on request
Supporting bracket	W / H / B...L	80/60/3		80/60/4
Core hole or recess		≥ Ø 140 x 200		≥ Ø 250 x 220
Attachment in mortar		Expanding mortar MG III		Expanding mortar MG III
Attachment in concrete		≥ C12/15		≥ C12/15
Values apply for facing bricks 115 mm thick with a superimposed load < 2 storeys, otherwise the anchor must be adapted in accordance with DIN 1053 Other dimensions on request

Recommended anchor selection
Superimposed Load(m)	Load (kN/m)	Anchor spacing ak (m)	Load stage	Intermediate bracket
< 1,50	< 3,105	1,00	3,5	WA-Z-95/50/3-980
< 2,00	< 4,140	0,75	3,5	WA-Z-95/30/3-730
< 3,00	< 6,210	1,00	7,0	WA-Z-95/50/3-980
< 4,50	< 9,315	0,75	7,0	WA-Z-95/30/3-730
< 6,00	< 12,420	0,50	7,0	WA-Z-95/20/2-480
(Assuming a 115 mm wide facing brick with γ=18kN/m³. Note individual evidence of attachment!)

Cross-references for additional information
Subject
Wall support with MOSO angle-bracket anchor type WK-M
Intermediate bracket with MOSO angle support type WA-Z
Lintel formation with MOSO accessories DB•GH•HB•GB•TA
Technical regulation governing masonry support (DIN 1053)
Principles for dimensioning masonry support

Errata and technical changes reserved.

Single-bracket anchors EK-M