Befestigungstechnik

Eggeweg 2a
32139 Spenge

Telefon: 05225 / 8799 - 0

Ingrid Bartling

Vertrieb Abt. MFixings - Projektleiterin Fassadenbefestigungen/Kalkulation

Telefon:05225 / 8799 - 320

Fax:05225 / 6710

Volker Schwab

Vertrieb Abt. MFixings - Projektleiter Fassadenbefestigungen/Kalkulation

Telefon:05225 / 8799 - 430

Fax:05225 / 6710

Universal anchors

Single-bracket anchors EK-U

The MOSO single-bracket anchor type EK-U is a universal achor for supporting brick facework.

Different versions allow these anchors to be used for virtually all purposes on building sites.

Constant stock of standard sizes for fast delivery
Flexible use, with or without intermediate bracket
Height-adjustable
Wall clearances greater than 200 mm are also possible for increased thermal insulation. As well as our MOSO support brackets, we will also obtain specific approval for our air gap wire anchor based on DIN 1053
Matching, approved air gap wire anchors included in delivery

Single-bracket anchors EK-U

3,5kN - 25,0kN
20 - 200 mm

± 25mm
approved stainless steel
type-testing or structural analysis

Single-bracket anchors EK-U

• Particularly suitable for invisibly supporting large wall surfaces.

• Variable anchor spacing (ak) depending on load and brick format (25 cm intervals).

• Install anchors at intervals ak and loosely fit intermediate brackets type WA-Z in between if necessary.

• The brackets must be fully supported until the brick mortar has set hard.
Particularly suitable for invisibly supporting large wall surfaces.
Variable anchor spacing (ak) depending on load and brick format (25 cm intervals).
Install anchors at intervals ak and loosely fit intermediate brackets type WA-Z in between if necessary.
The brackets must be fully supported until the brick mortar has set hard.

Single-bracket anchors EK-U

Technical data
Type / Version Type /Version	Load stage	3,5 kN		7,0 kN		10,5 kN
Type / Version Type /Version	Distance/wall	Cantilever length K	Bracket height x	Cantilever length K	Bracket height x	Cantilever length K	Bracket height x
	20 - 50	130	150	130	200	130	250
	40 - 70	150	150	150	200	150	250
	60 - 90	170	150	170	200	170	250
	80 - 110	190	150	190	200	190	250
	100 - 130	210	150	210	200	210	250
	120 - 150	230	175	230	250	230	300
	140 - 170	250	175	250	250	250	300
	160-190	270	175	270	250	270	300
	180-200	290	175	290	250	290	300
	Wall clearances greater than 200 mm available on request
Supporting plate	B / L / S	80 / 60 / 3		80 / 60 / 4		80 / 60 / 5
Max. size of fastener		up to M12		up to M12		up to M16
Shear connector for uncracked concrete > C20/25 (compression zone)		UPAT UKA3 M10x165 Distance from edge ar ≥ 110		UPAT UKA3 M12x190 Distance from edge ar ≥ 135		UPAT UKA3 M16x215 Distance from edge ar ≥ 155
Shear connector for cracked concrete > C20/25 (tension/compression zone)		Fischer FHB II-AS M10x60/60 Distance from edge ar ≥ 100		Fischer FHB II-AS M12x75/60 Distance from edge ar ≥ 140		Fischer FHB II-AS M16x95/60 Distance from edge ar ≥ 140
HK screw on supporting anchor rail in concrete > C20/25		MHK 38/17 M12x80 Distance from edge ar ≥ 75		MHK 50/30 M12x80 Distance from edge ar ≥ 150		MHK 50/30 M16x100 Distance from edge ar ≥ 200
Bear anchor rail		MBA 38/17K		MBA 50/31		MBA 52/34
Values apply for facing bricks 115 mm thick with a superimposed load < 2 soreys, otherwise the anchors must be adapted in accordance with DIN 1053. Other dimensions on request

Recommended anchor selection
Superimposed Load(m)	Load (kN/m)	Anchor spacing ak (m)	Load stage	Intermediate bracket
< 1,5	< 3,105	1	3,5	WA-Z-95/50/3-980
< 2	< 4,14	0,75	3,5	WA-Z-95/30/3-730
< 3	< 6,21	0,5	3,5	WA-Z-95/20/2-480
< 4,5	< 9,315	0,75	7	WA-Z-95/30/3-730
< 6	< 12,42	0,5	7	WA-Z-95/20/2-480
< 9	< 18,63	0,5	10,5	WA-Z-95/20/2-480
< 12	< 24,84	0,375	10,5	WA-Z-95/20/2-360
(Assuming a 115 mm wide facing brick with γ=18kN/m³. Note individual evidence of attachment!)

Cross-references for additional information
Subject
Edge formation with MOSO-single-bracket type EK-W
Corner formation with MOSO angle-bracket anchors type WK-E
Intermediate brackets with MOSO angled support type WA-Z
Lintel formation with MOSO accessories DB•GH•HB•GB•TA
Individual evidence of attachment in the anchorage base: Fischer FHB II-AS - For attachment in cracked concrete Hilti HVZ-R - For attachment in cracked concrete Fischer FAZ - For attachment in cracked concrete Hilti HST-R - For attachment in cracked concrete MBA - For attachment to the anchor rail UPAT UKA3 - For attachment in uncracked concrete UPAT UPM 44 - Other attachments
Technical regulation governing masonry support (DIN 1053)
Installation instructions for MOSO supporting anchors: With dowl On anchor rail
Principles for dimensioning masonry support

Errata and technical changes reserved.

Single-bracket anchors EK-U

: Different intervals between anchors can be achieved with the intermediate bracket type WA-Z.