The flexible solution for small loads

Single-bracket anchors EK-W

: MOSO single-bracket anchor tape EK-W as first anchor after an expansion joint.

The MOSO single-bracket anchor type EK-W with angled support is the ideally complements to the MOSO single-bracket anchor type EK-U near expansion joints and at the edge.

A complete brick can be laid securely on account of the free support.

Your advantages at a glance:

Constant stock of standard sizes for fast delivery
Quick and easy assembly - can also be used in combination with the MOSO perforated strip
Height-adjustable
Wall clearances greater than 200 mm are also possible for increased thermal insulation. As well as our MOSO support brackets, we will obtain specific approval for our air gap wire anchor based on DIN 1053
We also supply the matching, approved air gap wire anchors at low cost

Single-bracket anchors EK-W

Product information

Load stages:
Distance from the wall:
Height adjustment:
Material:
Evidence:

3,5kN - 7,0kN
20 - 200 mm

± 25mm
approved stainless steel
type-testing and structural analysis

Single-bracket anchors EK-W

Use and application

With single-bracket anchor type EK-U as first/last anchor near expansion joints/edge.
As supporting bracket for supporting lintels with MOSO perforated strip and openings >2.5 m long.
With welded-on gudgeon for supporting prefabricated concrete elements.
Masonry support near piers, as well as for small areas of wall.
The bracket must be fully supported until the brick mortar has set hard.

Single-bracket anchors EK-W

View tables

Technical data
Type /Version	Load stage	3,5 kN		7,0 kN
Type /Version	Distance/wall	Cantilever length K	Bracket height x	Cantilever length K	Bracket height x
	20 - 50	130	150	130	200
	40 - 70	150	150	150	200
	60 - 90	170	150	170	200
	80 - 110	190	150	190	200
	100 - 130	210	150	210	200
	120 - 150	230	175	230	250
	140 - 170	250	175	250	250
	160 - 190	270	175	270	250
	180 - 200	290	175	290	250
	Wall clearances greater than 200 mm available on request
Supporting bracket	W / H / B...L	110/60/6...120		110/60/8...130
Max. size of fastener		up to M12		up to M12
Shear connector for uncracked concrete ≥ C20/25 (compression zone)		UPAT UKA3 M10x165 Distance from edge ar ≥ 110		UPAT UKA3 M12x190 Distance from edge ar ≥ 135
Shear connector for cracked concrete > C20/25 (tension/compression zone)		Fischer FHB II-AS M10x60/60 Distance from edge ar ≥ 100		Fischer FHB II-AS M12x75/60 Distance from edge ar ≥ 140
HK screw on supporting anchor rail in concrete ≥ C20/25		MHK 38/17 M12x80 MBA 38/17K Distance from edge ar ≥ 75		MHK 50/30 M12x80 MBA 50/31 Distance from edge ar ≥ 150
Values apply for facing bricks 115 mm thick with a superimposed loas < 2 storeys, otherwise the anchors must be adapted in accordance with DIN 1053. Other dimensions on request

Recommended anchor selection
Superimposed Load(m)	Load (kN/m)	Load stage
< 1,50	< 3,105	3,5
< 2,00	< 4,140	3,5
< 3,00	< 6,210	3,5
< 4,50	< 9,315	3,5
< 6,00	< 12,420	3,5
< 9,00	< 18,630	7,0
(Assuming a 115 mm wide facing brick with γ=18kN/m³)

Cross-references for additional information
Subject
Lintel support with MOSO perforated strip
Wall support with MOSO single-bracket anchors type EK-U
Individual evidence of attachment in the anchorage base: Fischer FHB II-AS - For attachment in cracked concrete Hilti HVZ-R - For attachment in cracked concrete Fischer FAZ - For attachment in cracked concrete Hilti HST-R - For attachment in cracked concrete MBA - For attachment to the anchor rail UPAT UKA3 - For attachment in uncracked concrete UPAT UPM 44 - Other attachments
Technical regulation governing masonry support (DIN 1053)
Installation instructions for MOSO supporting anchors: With dowl For attachment to cast in channel
Principles for dimensioning

Errata and technical changes reserved.

Single-bracket anchors EK-W

Technical drawings

: MOSO single-bracket anchor type EK-W.

: Top view, type EK-W together with type EK-U.

: EK-WV, with offset.

: EK-W with perforated strip.

: EK-WS with gudgeon.